Are you ready to power up your Peloton again? If the power cord on your Peloton Bike or Tread has become damaged or stopped working, you’ll need to immediately replace it before using it again.
Replacing a Peloton’s power cord is a relatively simple process, but it’s crucial to follow the steps carefully to ensure you’ve installed the cable correctly and safely.
This informative guide will walk you through the Peloton power cord replacement process– from start to finish. We’ll also discuss some factors to consider when buying a third-party cable to help you make the best choice for your needs. Let’s get started!
Tools and Materials Needed
Before you begin replacing the power cord on your Peloton, make sure you have the following tools and materials on hand:
- New Peloton Power Cord
- Philips Head Screwdriver (only applicable for replacing monitor cable)
- 3mm Allen Key (only for monitor cable replacement)
Replacing Peloton Bike / Bike+ Power Cable
Start by unplugging your Peloton’s power adapter from the wall outlet as a safety precaution before working with electrical components. Next, disconnect the older cord from your Bike’s power jack, located on the base of the equipment just above the rear stabiliser. Unplug the other end from the adapter itself.
After that, plug the replacement power cord into your bike’s power jack. Connect its other end to the power adapter, ensuring the cable’s inserted correctly and firmly on both sides. Finally, plug the adapter back into its outlet.
Assuming you see the green light on the power adapter (or the white light at the end of the power cord for Bike+), you can turn on your Peloton Bike by pressing the Power button at the back of the touchscreen.
To prevent damage to the new power cord or adapter from sweat, spills, bends, and tangles, avoid running the power cable underneath your Bike. Peloton strongly recommends against plugging it into a GFCI outlet and using power strips/extension cords.
Replacing the Bike’s Monitor Power Cord
If the power cord to your Peloton’s touchscreen monitor is faulty, replacing it is slightly more complicated. However, with the required tools and our step-by-step instructions, you’ll get your Peloton Bike’s monitor up and running in no time.
- Unplug your Peloton Bike from the wall outlet.
- Lock the flywheel by turning the resistance knob fully to the right.
- Use your 3mm Allen Key to detach the water bottle holder.
- Next, unscrew the two screws at the front holding the sweat guard with a Philips-head screwdriver, then the bottom two screws on the side.
- Pull the bottom part of the sweat guard toward yourself to detach the entire assembly.
- After that, disconnect the monitor power cord from the back of the touchscreen. Follow it down to the other end.
- There should be a wire bracket holding the cable in place. Gently squeeze the bracket’s sides to detach it from the bike’s frame fork, then disconnect the power cable by pulling on it.
- Connect the colour-coded connectors on the new monitor power cord to the ones on the Bike. Ensure the colours match, with the arrows aligned and the connectors firmly seated.
- Align the connectors to the wire bracket, then put it back inside the frame fork. You can do it by fitting one side of the bracket into the fork’s slot and squeezing the other side into the other.
- Now plug the monitor power cord into the bike’s touchscreen.
- Refit the front sweat guard, installing the front-top and bottom-side screws using your screwdriver and the bottle holder using the 3mm Allen Key.
And that’s how you replace your Bike’s monitor power cord. Hopefully, the monitor should turn on when you plug your Bike in the mains and press the Power button.
Where to Get a Replacement Peloton Power Cord?
If your Peloton Bike, Tread, or Row isn’t turning on, immediately reach out to Peloton Member Support for troubleshooting. Once they confirm it’s an issue with the equipment’s power cord or adapter, they’ll ship you a replacement part at no cost as long as your Peloton is warranty-covered. As for an out-of-warranty replacement, Peloton will charge you for the power cord and shipping.
If the price to pay for the replacement is too much, or Peloton doesn’t have them in stock, you may also look for third-party Peloton power cords/adapters on e-commerce shopping sites like Amazon.
Best Peloton Power Cord Replacement
Things to Consider Before Buying Peloton Power Cord
However, when purchasing one, there are a few factors that you should keep in mind:
Make sure the power cord you purchase is compatible with your Peloton equipment. Some power cords may only work with select models or revisions. Here are the recommended power requirements for all Pelotons:
- Peloton Bike / Bike+: 100-240 V, 50-60 Hz, 3.25 A
- Peloton Tread: 120 V, 60 Hz, 15 A
- Peloton Row: 100-240 V, 50-60 Hz, 0.5A
You must choose a power cord made of high-quality materials and is built to last. Look for options that have been tested thoroughly for safety and durability.
As with any product, price is an important consideration. While it may be tempting to opt for the cheapest Peloton power cord available, it’s crucial to remember – “You get what you pay for.” Choose a reasonably-priced one that’s also well-reviewed.
Similar Peloton Articles
- Best Peloton Water Bottle Holders
- Fix Peloton No Command Issue
- How to Fix Peloton Metrics Not Working
- Peloton iPad Holder Reviews
- Peloton Touch Screen not Working? A Quick Fix Guide
Replacing the Peloton power cord is a straightforward process that can be done in a few easy-to-follow steps. By following the outlined instructions, you can get your Peloton gym equipment running again in no time. Happy cycling!
If your Peloton Bike, Tread, or Row doesn’t power on even after a cord replacement, it could simply be a result of a loose connection or faulty electrical outlet. Or, it may be an issue with the equipment itself, in which case you have no choice but to contact Peloton Support for further assistance.
As we mentioned earlier, remember to exercise caution when changing the power cord. And when looking for third-party alternatives, choose a high-quality power cord to ensure your Peloton stays powered up for the long haul.